Which Type of Sewing Pin Should You Use?
Different types of pins should match the fabric and task: use fine dressmaker pins for light woven fabric, glass head pins for pressing, long quilting pins for layers, and clips or safety pins where a pin would leave a hole. Match thickness, length and head style before you sew.
On this page (11 sections)
- Why do different types of pins matter for fabric and task?
- What are dressmaker pins and when should you use them?
- What are glass head pins and why do makers use them?
- What are quilting pins and how are they different?
- Are safety pins a good pin for quilting?
- What are corsage pins, hat pins and specialty pins?
- What are clips and when are they better than pins?
- What pin thickness and length should you use for each fabric?
- How do you pin seams so they stay straight?
- How should you store and care for sewing pins?
- Which type of sewing pin should you use for your next project?
Different types of pins should match thickness, length and head style to the fabric and task. Use fine dressmaker pins for light woven fabric, glass head pins when you will press, long quilting pins for layers, and clips where a pin hole would show.
This guide compares the common styles of pins by shaft, point and head. You will see when each type helps, when it can snag or leave a mark, and how to place pins so seams stay straight.
Why do different types of pins matter for fabric and task?
Different types of pins matter because shaft thickness and length control both hold and damage. A thin shaft slides into fine fabric with less distortion, while a thick shaft holds heavy layers but can leave a visible hole.
Head style controls how you handle the pin. A large round head keeps the pin from slipping through fabric and makes it easy to spot before sewing.
Point shape controls entry. A sharp point enters woven fabric cleanly, while a slightly rounded point can push knit threads aside instead of splitting them.
Pin length also affects control. A pin that is too short may hold only the top layer.
A pin that is too long can catch on the machine bed or pull the fabric out of alignment as you sew.

A size 80/12 sharp Microtex needle for precise stitching once your pins have held the seam in place.
See it on AmazonThe maker describes this needle as a slim acute point for straight stitches on cotton, silk, microfiber and other woven fabrics. A clean needle and a correct pin work as a pair, since both aim to enter fabric without dragging or distorting it.
The SCHMETZ listing specifies a slim acute point, size 80/12, manufacturer part number 1730, and compatibility with domestic sewing machines. That same logic applies to pins, since a fine point and a fine shaft both reduce the force needed to enter the fabric.
Rule: choose the thinnest pin that still holds the layers without bending.
What are dressmaker pins and when should you use them?
Dressmaker pins are the general purpose choice for light to medium woven fabric. They are usually about 1 to 1.5 inches long with a small head and a sharp point.
Use them for cotton piecing, shirt seams, hems and pattern fitting. The fine shaft keeps two light layers aligned without creating a large hole.
They are not ideal for thick quilts. A short dressmaker pin may not reach the bottom layer, so the layers can shift as you feed them under the presser foot.
Dressmaker pins also work well for matching plaids, stripes and other patterns. The small head lets you place the pin close to the seam line without adding bulk.
For very light fabric, check that the pin does not create a visible puncture when you remove it. A quick test on an offcut from the same fabric shows whether the shaft is fine enough.
How to place dressmaker pins for straight seams
Place pins perpendicular to the seam line, about 2 to 3 inches apart for light fabric. That spacing holds the seam without adding bulk under the presser foot.
Pin from the edge you will trim later when possible. This keeps pin heads away from the needle path.
For curved seams, add pins closer together on the curve. Keep them perpendicular to the local seam line rather than to the table edge.
Rule: use dressmaker pins for light woven seams and pin about every 2 to 3 inches.
What are glass head pins and why do makers use them?
Glass head pins are dressmaker style pins with a round glass head that resists iron heat. The head is larger and easier to see than a plain metal or plastic head.
Use them when you need to press a seam, set a pleat or shape a collar before stitching. You can leave them in place for a quick press, then remove them before sewing.
The glass head also gives you a grip when you pull the pin out. That matters when you work with several layers and need to move fast.
Glass head pins are still straight pins, so they do not lock like safety pins. For work that will be handled or turned, add a safety pin or a clip where a straight pin might work loose.

A 35wt all purpose polyester thread in white for hand basting or machine stitching after you pin the seam.
See it on AmazonCoats & Clark describes this thread as 100% polyester, 35wt, in a 6-pack of 400 yard spools. A medium weight thread suits general stitching, while a finer thread would suit very delicate fabric.
Rule: pick glass head pins when pressing is part of the task.
What are quilting pins and how are they different?
Quilting pins are longer and sturdier than dressmaker pins, often 2 to 3 inches or more. The extra length lets one pin pass through top fabric, batting and backing.
The shaft is thicker, so it resists bending when it crosses several layers. The head is usually large enough to find quickly and to stop the pin from pulling through.
Use them for basting a quilt sandwich, holding binding in place and pinning bulky seams. They give you fewer pins per quilt than dressmaker pins, but each pin does more work.
A thicker shaft distributes the hold across the full sandwich, so batting does not bunch between pins. That is different from piecing, where a fine pin is enough because cotton layers are thin and flat.
What length should you choose for quilting?
Choose a pin that clears the full thickness with a little shaft left above the top layer. Too short a pin will not lock the layers, and too long a pin can catch on the machine bed.
For a thin quilt, a 2 inch pin is often enough. For a thick batting or a bulky seam, a 3 inch pin gives you more reach.
Test the length on a corner of the sandwich before you pin the whole quilt. If the point just reaches the backing, the pin will hold.
Rule: use long quilting pins that pass fully through the thickest part of the quilt.
Are safety pins a good pin for quilting?
Safety pins are a strong choice for basting and for holding layers that need to stay put during handling. They lock closed, so they do not slide out like straight pins.
Use curved safety pins for quilt basting because the curve follows the layer and reduces shifting. Place them in a grid pattern, often 4 to 6 inches apart, then remove them as you quilt.
They do leave a hole, so test on a hidden area with silk or other mark prone fabric. For delicate fabric, clips or hand basting may be safer.
The locking head also matters during turning and binding. A straight pin can open a gap when the work is flipped, while a closed safety pin keeps the layers together.
Safety pins are less precise than straight pins for matching a seam line. Use them for basting and bulk holding, then switch to dressmaker pins when you need exact alignment.
If you want another option, read Can You Quilt without Pins? for basting methods that avoid pins in the fabric.
Rule: use safety pins for basting and for work where a straight pin could slide out.
What are corsage pins, hat pins and specialty pins?
Corsage pins, hat pins and specialty pins are long pins with a decorative or ball head for specific jobs. They are not everyday seam pins for most sewing.
A corsage pin has a small round head and is used for flowers, name tags and light holding tasks. A hat pin is longer and sturdier and is used to secure a hat.
Specialty pins include pins for knits, leather and upholstery. A knit pin may have a fine point that spreads threads, while an upholstery pin is thick enough for heavy fabric and padding.
These pins solve narrow problems rather than replacing dressmaker or quilting pins. Keep a few for craft and repair jobs, but do not rely on them for precise seam alignment.
A specialty pin should be matched to the material in the same way a needle is matched. The SCHMETZ Microtex listing specifies size 80/12 and a slim acute point for cotton, silk, microfiber, polyester, foils, artificial leather, coated materials, cork, batiks and bamboo.
Rule: use specialty pins only for the narrow job they were made for.
What are clips and when are they better than pins?
Clips are not pins, but they often work better when a pin hole would show. A clip holds layers with pressure and leaves no puncture.
Use clips for silk, velvet, knits, leather and laminated fabric. They also help with binding, straps and bulky seams where a pin would bend.
Clips do add height, so they can shift fabric under a presser foot if you place too many near the needle. Keep them back from the stitch line and remove them as you go.
How to space clips for even hold
Space clips evenly so pressure is shared across the seam. Crowding clips at one end can pull the fabric, while a gap in the middle can let layers separate.
Rotate the clip so the flat side sits against the fabric where possible. That spreads pressure and reduces the chance of a mark on delicate surfaces.
For binding, place clips close enough to hold the fold in place, then remove each clip just before the needle reaches it.
For a fuller view of pinning choices, see our Best Quilting Pins For Home Use guide.
Rule: choose clips over pins when fabric marks easily or a pin shaft would distort the seam.
What pin thickness and length should you use for each fabric?
Pin thickness and length should rise with fabric weight and layer count. Fine fabric needs a fine, short pin, while thick layers need a thicker, longer pin.
For voile, lawn and other light woven fabric, use a fine dressmaker pin. The thin shaft enters with little force and leaves a smaller hole.
For quilting cotton, use a standard dressmaker pin for piecing and a long quilting pin for the full sandwich. The thicker shaft holds weight without bending.
For denim, canvas and upholstery fabric, use a sturdy pin or a clip. A fine pin can bend or break, and it may not hold the seam under the presser foot.
Consider the number of layers as well as the fabric itself. Two layers of cotton need less hold than one layer of canvas plus batting and backing.
As layer count rises, move to a longer and thicker pin.
The needle choice follows the same principle. The SCHMETZ Microtex size 80/12 is listed for microfibers, polyester, silk, foils, artificial leather, coated materials, cork, batiks, bamboo and cotton, with a slim acute point for precise stitches.

A needle threader for hand sewing needles from size 1 to 11 when you switch from pinning to hand basting.
See it on AmazonBohin describes this threader as a compact, one piece tool for hand sewing, quilting and embroidery. It helps you thread a hand needle quickly after you have placed pins or clips.
The Bohin 81980 listing specifies one piece per package, plastic construction, item length 7.62 centimeters, and suitability for needle sizes 1 through 11. That range covers fine to standard hand needles.
Rule: match pin thickness to fabric weight, and never force a fine pin through heavy layers.
How do you pin seams so they stay straight?
Straight seams start with pins placed at right angles to the seam line and spaced evenly. That pattern holds the fabric without pulling it sideways.
Start by matching raw edges and notches, then pin at the start, middle and end. Add pins between those points until the fabric does not shift when you lift it.
Pin parallel to the seam line only when you need to hold a fold or a pleat. Cross pinning gives more control for seams you will sew at once.
Remove pins before the needle reaches them. A needle that strikes a pin can bend, break or mark the fabric.
Thread choice matters after pinning as well. The Coats & Clark listing describes a 35wt, 100% polyester all purpose thread, 400 yards per spool, in a 6-pack in white, with a polyester covered polyester core for strength.
For thread choice after pinning, compare options in our quilting thread guide.
Rule: pin perpendicular to the seam, space pins evenly, and remove each pin before the needle reaches it.
How should you store and care for sewing pins?
Pins stay useful when you store them dry, sorted by type and protected from bending. A pincushion, a magnetic dish or a small tin all work if they keep points from dulling.
Keep dressmaker pins, quilting pins and safety pins in separate places. Mixed storage bends fine points and makes sorting slow when you start a project.
Check pins before use. Discard a pin if the point is bent, the shaft is rusty or the head is loose, since a damaged pin can snag fabric or leave a mark.
Replace pins that you use for thick quilts more often. Repeated passes through batting and backing can dull the point faster than light cotton sewing.
Sort by length as well as type when you can. A short dressmaker pin stored with long quilting pins is easy to grab by mistake.
Keep the storage container closed or covered when the pins are not in use. That protects points from knocks and keeps pins from rolling onto the table.
Rule: store pins by type, discard bent or rusty pins, and test a dull point on scrap fabric before you use it on a quilt.
Which type of sewing pin should you use for your next project?
Different types of pins work best when you match the pin to fabric weight, layer count and whether you will press the seam. Use fine dressmaker pins for light woven fabric, glass head pins for pressing, long quilting pins for full layers, safety pins for basting and clips where a hole would show.
Keep three basics in your sewing room. A pack of dressmaker pins covers most seams, long quilting pins cover quilt sandwiches, and clips cover delicate or bulky work.
Test any pin on a hidden area of silk, knit or other mark prone fabric. That one test saves you from a hole that stays in the finished piece.
Plan the sequence before you start. Pin or clip the seam, press if the head style allows it, then stitch with a needle matched to the fabric.
The SCHMETZ Microtex 80/12, the Bohin threader for sizes 1 to 11, and the Coats & Clark 35wt polyester thread each cover a different step in that sequence.
Final rule: pick the thinnest pin that holds the layers, the shortest length that reaches through them, and a head style you can see and grip.
Frequently asked questions
What are the different types of pins for sewing and quilting?
The main types are dressmaker pins, glass head pins, quilting pins, safety pins, corsage pins, hat pins, clips and specialty pins for knits or leather. Each type differs by shaft thickness, length, point and head size, so you match the pin to fabric weight and the hold you need.
Which pin is best for quilting layers?
Long, sturdy quilting pins are best for holding two or more layers because they reach through batting and backing without bending. Use fewer, well placed pins and remove them as you sew so the needle does not strike a pin head.
Can you use glass head pins with an iron?
Yes, glass head pins are made to resist heat from an iron, so you can press a seam without removing every pin first. Keep the iron moving and check the pin head for softening if you use high heat for long periods.
Do pins leave holes in fabric?
Pins can leave small holes, especially in silk, knits and tightly woven fabric. Test a pin on a hidden area first and use clips or a hand basting stitch where a mark would show.
About this guide: Our look at different types of sewing pins draws on maker specs, materials and what owners report. See how we research.



